GPS drivers for Window 10.Bu 353 driver windows 10

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

If the LED is off there is no power being received. Check the connection. Try moving the GPS receiver to a clear location. This will require repeating steps above. The red indicator led will not work. Unpack and start. Set correct Baud rate and and com port as above. Click connect to data source button. First make sure to. This may lead to navigation errors. Tested and GNSS sensor seems to be able to pick up the signal quite well.

Author Petr Simons Home page on bitbucket is now gone, so use the link above. When you get done, test your installation for gps accuracy. Especially moving slowly, check if the course is stable. Many internal gps chips are not up to the task. Takes a lot of smoothing on the side of the software in use.

On many mobile devices with gps built-in the gps must be switched off and connected to a nmea gps data stream over wifi. Much more stable. Quality tablets and phones do not show this limitation.

Read more in Connections for Linux. The response will be all groups that the user belongs to. If not, you have to add your user to this group. Logout of your current session for group changes to take effect. All major Linux distribution includes a graphical user settings dialog, where adding a user to a group, could be fixed.

If this is a new installation, click on the Toolbox icon and configure your GPS source, chart directories, and other settings. More user experience of setting up bluetooth GPS are welcome, as the notes below just reflects a few users experience. Please use the Forum. Once you have done that you will need to find what the address of the GPS is. To do that you run this command:. You should see something similar to:. We do this with the following command:. Note put your GPS address in this line You should not have to run these commands each time your linux is restarted as it will remember your GPS address.

Text should be:. If it works, try running opencpn without sudo, chances are that you cannot see the gps. Note that you can add it yourself by writing directly into the scroll down box.

Make sure you belong to that group. Both those companies make OS X drivers available on their web sites, but manufacturers of GPS devices usually package the driver with device.

When the driver is installed and the device connected, start OpenCPN, select the Options icon and click the Connections tab. Select Serial. If the correct selection has been made, you should see the GPS status icon change from red to green. For those that want to following Patinka’s method from 15 in this thread Many thanks Chris! U-Blox 7 drivers. However experienced users are invited to report the specifics about using USB ports with Virtual Configurations.

Please be specific about the setup and software and explain how virtual USB ports work in that environment. These commenta will eventually make their way into this section. This can affect the connection and reliability of the connection for GPS. OpenCPN is user powered, so we depend on User’s sharing their experiences. Please assist us. Trace GPS Setup. Share via Share via GPS Setup Below we describe only the basics of getting a gps up and running.

So numbers of satellites in view can alter between 1 to 14 or so. The GGA sentence though is used to indicate satellites in use for the fix calculation.

Use the manufacturers software U-blox Center, GpsInfo, etc. Install and run the manufacturers software this is not the driver, that is installed already for the device.

Then be sure to turn of the Manufacturer’s Software as it has captured the port, such that it will not be available to Opencpn. Choose Driver. Select bits per second, 8 data bits, None parity, 1 stop bit, and None for Flow Control.

Start OpenCPN. Click on the Options Icon. Launch this program to install the diagnostic utility. Click on the ToolBox Icon. Install the gpsd and gpsd-clients packages. On Ubuntu, that is really all you have to do, but see next point. When you plug in your gps this will trigger gpsd to start. At least on Ubuntu The support for this chip is turned off by default.

Save and restart your computer. If xgps or cgps isn’t working, it’s a gps or gpsd problem, not an OpenCPN problem. Make sure that gpsd isn’t running then connect your gps and start OpenCPN. This thread is locked. You can follow the question or vote as helpful, but you cannot reply to this thread.

I have the same question Report abuse. Details required :. Cancel Submit. In reply to PatriciaWatson’s post on February 4, How satisfied are you with this reply? Thanks for your feedback, it helps us improve the site. Are you getting a number after com port error. In Device Manager do you see a yellow exclamation or triangle beside the com port.

This site in other languages x.

 
 

 

Bu 353 driver windows 10.usb gps receiver BU-353 V1.03

 

I am trying to run my usb gps receiver BU V1. Keep getting “com port error”. Any other suggestions please? The site link below will allow you to get your manuals and also in support be able to download a Windows 7 driver. Once installed try to run in Compatibility mode. I have not seen a Windows 8 driver anywhere.

Was this reply helpful? Yes No. Sorry this didn’t help. Thanks for your feedback. Choose where you want to search below Search Search the Community.

Search the community and support articles Windows Windows 8 Search Community member. Thanks Patricia. This thread is locked. You can follow the question or vote as helpful, but you cannot reply to this thread.

I have the same question Report abuse. Details required :. Cancel Submit. In reply to PatriciaWatson’s post on February 4, How satisfied are you with this reply? Thanks for your feedback, it helps us improve the site. Are you getting a number after com port error. In Device Manager do you see a yellow exclamation or triangle beside the com port.

This site in other languages x.